42213 Sarah Way, Temecula, CA 92590,
Tel: 800-854-8530 (USA)
Micro Series 1/8 DIN
& Remote Displays
5 or 6 Digits, Choice
of 3 Digit Heights
Programmable meters with a wide choice of analog and
digital I/O cards
measurement, control, and remote display.
Standard digit height of 0.56". Also available as large digit displays with
1" digits or
Micro-C 6-digit counter in 1/8 DIN case.
Models Micro-P & Micro-C
- The state of
the art in programmable digital panel meters,
counters, timers, and serially driven remote
- Wide choice
of signal conditioners for analog and digital
- Wide choice
of outputs for control, alarm and data
performance for 5-digit digital panel meters:
(60 readings / sec) with
99.99% accuracy for DC
performance for 6-digit digital counters and rate
High speed (up to 25 readings / sec) with 6-digit
resolution for frequency or rate.
performance for serially-driven remote displays:
with RS485, up to 31 remotes addressable on on data line, each
with optional local analog and setpoint outputs.
- All DPM and
counter ranges user-selectable and factory
95-240 Vac ±10% power supply standard, low voltage AC or
DC power supply optional.
- Easy setup and
- Available in 1/8 DIN
case panel meter size with
or green 0.56" high LED digits.
- Also available in
large-digit versions for long-distance viewing:
1" digits (Mighty-1), 5"
- Two-year warranty.
digital panel meters, counters, timers and
serially-driven remote displays are an
exceptional value by providing high performance at
minimum cost, as made possible by state-of-the-art
circuit design and firmware. Modular design and a
wide range of plug-in options allow the Micro Series
to be configured for a wide range of applications
from simple measurement to control and
communications as part of a data network.
Micro Series base
models, as featured in this web page, provide
0.56" high red or green LED digits, and are housed
in a standard 1/8 DIN size panel-mount case (48 x 96
mm panel cutout). All power and signal connections
are via push-in screw-clamp connectors.
using the same signal conditioning boards, I/O
boards, and firmware, are also available for viewing
across a plant floor or outdoor yard: 1" digits (Mighty-1) and 5" digits (Mighty-5).
The Mighty-5 features sunlight-readable,
ultra-bright LED digits, plus a NEMA-4X housing
which can be installed outdoors in any weather.
hardware modules of a Micro Series instrument or
remote display are a power supply, display
subsystem, signal conditioner board, and
microcomputer board. Different microcomputers boards
are used depending on the application (DPM or
counter, standard or extended). Three slots are
provided to plug in an optional alarm / setpoint
controller board, an analog output board, and a
communications board. In combination with firmware
and user-programmable selections, these modules
provide a rich set of solutions for industrial
measurement, display, and control applications:
5-Digit Analog Meters by Application:
6-Digit Counters & Timers by Application:
DC Digital Panel Meters: DC Volts, mV,
Digital Panel Meters: True AC rms Volts, mV, Amps, mA.
Meters: Scalable display for signals such as 0-1 mA, 4-20 mA, 0-10 V.
Process Signal Totalizers: Totalizing for 0-1 mA, 4-20 mA or 0-10 V signals.
& Potentiometer Followers: Sensitivity to ±200 mV full
scale, 4-wire bridge connection.
Microvolt & Load Cell Meters:
Sensitivity to ±20 mV full scale, 4- or 6-wire bridge connection.
Meters: Special capabilities
for weighing applications.
Temperature Meters: Multiple thermocouple & RTD types
6-Digit Serially-Driven Remote Displays:
Frequency & Rate Meter:
Two independent scalable pulse-input channels from
0 Hz to 1 MHz to display frequency, rate, RPM, or flow
Up/Down Totalizer (pulse
input): Two independent scalable pulse-input
channels count up or down to a preset at rates up to
1 MHz. Ideal for turbine flow meters. Scaled rate and total in same instrument.
A+B, A-B, A*B, A/B,
A/B-1 Draw Meter: Arithmetic functions (+, -, /, x) on dual channels
A & B. For example, add or subtract rates from two flow
meters for combined scaled flow or volume. Display ratio of
flow rates, RPM of rollers, or speed of moving belts.
Batch Controller (pulse input):
A low-cost controller with up to three relays for
repetitive fill operations.
Batch Controller (analog input):
Same capabilities as pulse-input batch controller, but
for 0-1 mA, 4-20 mA or 0-10 V process signals.
single-events from 1
µs to 99
hours with a timing resolution to
0.2 µs, or
accumulate multiple events to 999,999 hours.
Time Interval Meter: Time periodic events from 1 µs to 199.99 s over a
programmed gate time up to 199.99 s with a timing resolution to 0.2 µs.
Phase Angle Meter: 20 updates per second for low frequencies,
such as AC line frequency.
A resolution of 1º, 0.1º or
0.01º is user-selectable.
Duty Cycle Meter:
Displays ON or OFF
period as a percentage of total period over a programmed
gate time from 10 ms to 199.99 s.
Scalable position or rate from quadrature shaft encoder
Serially Driven 6-Digit Remote Display:
RS232 interface for point-to-point communications, or RS485
for up to 31 addressable displays on same
data line. Each remote can provide independent setpoint control
and an analog output tied to the display.
Micro & Mighty Series
Micro & Mighty Series
to Micro Series with 0.56" digits and 1/8 DIN case)
7-segment, bright LED digits, red or green.
0.56" (14.2 mm)
-99,999 (digital panel meters for analog signals)
-999,999 (counters, timers, analog totalizers, remote displays)
-999,990 (scale / weigh meter with dummy zero)
Minus sign, 2 setpoints, selectable decimal points
| Dual slope
±0.1% of full scale
±1 count (typ., DC signals)
60/sec at 60 Hz,
50/sec at 50 Hz
at 60 Hz, 3/sec at 50 Hz
update rate, max
| Inverse period
0 to 1 MHz
±1 ppm / ºC
30 ms +
0-2 signal periods
95-240 Vac ±10% standard,
12-34 Vac optional.
95-370 Vdc standard, 10-48 Vdc optional.
3 W (typ.)
5 Vdc ±
5%, 100 mA max, 10 Vdc ± 5%, 120 mA max,
24 Vdc ± 5%, 50 mA max
from front when panel mounted
0ºC to 55ºC (32ºF to 131ºF)
-40ºC to 85ºC (-40ºF to 185ºF)
Connections (power & data)
"Case Dimensions & Mounting" below
230 g (8 oz) typ.
screw clamp connectors at rear of case.
Case Dimensions & Mounting
to 1/8 DIN case for 0.56" digits)
Micro & Mighty Series Downloads